Mulch Calculator
Cubic yards and bags of mulch for beds, borders and tree rings.
Mississippi State Extension suggests a layer of 2 to 3 inches for most uses.
Covers settling and uneven ground.
The volume is printed on the bag.
Examples: , ,
Enter length, width and depth to see how much mulch you need.
Short answer
Multiply the area of the bed by the depth of the layer, both in feet, to get cubic feet. Add extra for settling, then divide by 27 for cubic yards. For bags, divide by the volume printed on the bag.
On this page
How do I use the mulch calculator?
- Pick a shape: Rectangle for a bed or border, Circle for a tree ring, or Known area if you already measured it.
- Enter the measurements and the depth. You can type feet and inches together:
12,12.5and12' 6"all work. - Keep the extra at 10%, or change it.
- Read the cubic yards. For bags, type the bag size from the label.
How is the volume worked out?
Mulch is a volume: the area of the bed times the depth of the layer. The depth is the finished layer, so the extra covers settling and uneven ground.
- Area of a rectangleArea = L × W
- Area of a circleArea = π × (D ÷ 2)²
- VolumeV = Area × d
- Total with extraTotal = V × (1 + x ÷ 100)
- BagsBags = round up (Total ÷ B)
Round up means to the next whole number. Bags show only when you enter B.
| Symbol | Meaning | Unit |
|---|---|---|
| L | Length of the bed | ft (m) |
| W | Width of the bed | ft (m) |
| D | Diameter of a round bed | ft (m) |
| d | Depth of the finished layer | in (cm) |
| x | Extra for settling | % |
| B | Volume of one bag, from the label | ft³ (L) |
Worked example
A bed that is 12 feet by 10 feet, with a 2 inch layer and the default 10% extra.
| Shape | Rectangle |
|---|---|
| Length | 12' 0" |
| Width | 10' 0" |
| Depth | 2" |
| Extra for waste | 10% |
| Mulch needed | 0.81 yd³ |
|---|---|
| Without extra | 0.74 yd³ |
A common mistake
Measuring a curved bed as one big rectangle. A bed with a bulging edge is smaller than the box around it, and that gap turns into mulch you pay for and do not use. Pace out the bed in a few simple pieces, calculate each one, and add the results, or enter the area directly if you already know it.
How far does a cubic yard go?
The same cubic yard covers much more ground at 2 inches than at 4. This table is plain arithmetic, so you can check the calculator against it. A second table lists the cubic yards for beds of common areas, with 10% extra.
| Depth | 1 yd³ covers | 100 ft² takes |
|---|---|---|
| 1 in | 324 ft² | 0.31 yd³ |
| 2 in | 162 ft² | 0.62 yd³ |
| 3 in | 108 ft² | 0.93 yd³ |
| 4 in | 81 ft² | 1.23 yd³ |
| Bed area | 2 in deep | 3 in deep |
|---|---|---|
| 100 ft² | 0.68 yd³ | 1.02 yd³ |
| 250 ft² | 1.70 yd³ | 2.55 yd³ |
| 500 ft² | 3.40 yd³ | 5.09 yd³ |
| 1,000 ft² | 6.79 yd³ | 10.19 yd³ |
How deep should mulch be?
A Mississippi State University Extension article says a 2- to 3-inch layer is enough for most uses. It notes that many recommendations say 3 to 4 inches, and that layers as deep as 10 inches are way too much. More is not better.
The calculator has no default depth, so enter the one you choose.
| Layer | Depth |
|---|---|
| Enough for most uses | 2 to 3 in (5.1 to 7.6 cm) |
| Common recommendation | 3 to 4 in (7.6 to 10.2 cm) |
| Way too much | 10 in (25.4 cm) |
Around trees and shrubs
Spread the mulch out, not up. The article says never to pile it against the trunk or shape it like a volcano. Pull it back from the trunk and contour it like a shallow bowl, so it holds water over the roots.
Should I buy bags or bulk mulch?
Bags are easy to carry and good for a small bed. Bulk mulch comes by the cubic yard, usually delivered, and suits a big job. The calculator gives you both numbers, so you can compare the two before you order.
When you count bags, round up. A bag that is a little short is better than a bare patch at the end of the bed.
Frequently asked questions
How many cubic yards of mulch cover 1,000 square feet?
It depends on the depth. At 2 inches deep, 1,000 square feet takes 1,000 × (2 ÷ 12) = 166.7 cubic feet, which is 6.17 cubic yards before any extra. At 3 inches it takes 9.26 cubic yards.
How many square feet does a cubic yard of mulch cover?
At 2 inches deep it covers 162 square feet, and at 3 inches it covers 108. Divide 27 cubic feet by the depth in feet to get the area for any other depth. Add your extra on top if the mulch will settle.
How many bags of mulch make a cubic yard?
Divide 27 cubic feet by the volume printed on the bag. For example, with a 2 cubic foot bag, 27 ÷ 2 = 13.5, so you buy 14. Bag sizes differ by brand, so use the size from your bag.
Related calculators
- Topsoil CalculatorCubic yards, tons and bags of topsoil for a lawn or garden bed.
- Gravel CalculatorCubic yards, tons and bags of gravel for a path, driveway or base.
- Square Footage CalculatorArea of a rectangle, circle, triangle or trapezoid, in square feet, yards and meters.
- Fence CalculatorPosts, panels or pickets, and rails for a fence of any length.