Skip to content
Snapline

Roofing Calculator

Roof area, roofing squares and bundles of shingles from the size and pitch of your roof.

Unit system

Outside the walls.

Outside the walls, from eave to eave.

How far the roof reaches past the wall on every side. Leave empty for none.

Rise per 12 inches of run (for example, 4 for a 4:12 roof). Use 0 for a flat roof.

Covers cuts, hips, valleys and the starter row. More complex roofs need more.

Printed on the shingle packaging. It differs by product.

Examples: ,

??Gable end

Enter building length, building width and roof pitch to see the result.

Short answer

A sloped roof is bigger than the ground under it. Multiply the footprint by the slope factor to get the roof surface, then divide by 100 square feet to get roofing squares. Add your extra, and multiply by the bundles in one square from the packaging.

On this page

How do I use the roofing calculator?

  1. Enter the length and the width of the building, measured outside the walls, and the overhang if the roof reaches past them.
  2. Enter the pitch as the rise for every 12 inches of run, in whole numbers. A 6 means a 6/12 pitch. Use 0 for a flat roof.
  3. Keep the extra at 10%, or change it. A roof with many hips and valleys needs more.
  4. Read the roof surface and the squares. For bundles, type the number of bundles in one square from the shingle packaging.

How is the roof surface worked out?

The footprint is the roof seen from above, overhang included. The slope factor says how much longer the sloped roof is than the ground under it.

  • FootprintFootprint = (L + 2 × o) × (W + 2 × o)
  • Slope factorFactor = square root of (1 + (r ÷ 12)²)
  • Roof surfaceSurface = Footprint × Factor
  • SquaresSquares = Surface ÷ 100 ft²
  • BundlesBundles = round up (Squares × (1 + x ÷ 100) × b)

Round up means to the next whole number. Bundles show only when you enter b.

What the symbols mean
SymbolMeaningUnit
LBuilding length, outside the wallsft (m)
WBuilding width, outside the wallsft (m)
oOverhang past the walls, each sidein (cm)
rRise for every 12 in of runin
xExtra for cuts, hips and valleys%
bBundles in one square, from the packagingcount

One pitch for the whole roof

The calculator assumes every plane has the same pitch. Then the surface equals the footprint times the factor, for a gable, a hip or a single slope. If one part has a different pitch, such as a low porch roof, calculate it on its own and add the results.

Worked example

A house that is 40 × 30 ft with a 6/12 roof, no overhang and the default 10% extra. The 3 bundles per square and the price per bundle are example values for the calculation. Use the numbers on your own packaging and receipt.

You enter
Building length40' 0"
Building width30' 0"
Roof pitch6
Extra for waste10%
Bundles per square (optional)3
Price per bundle (optional)$36.00
You get
Roof surface1,342 ft²
Roofing squares, with extra14.76
Bundles45
Squares, before extra13.42
Slope factor1.118
Footprint, overhang included1,200 ft²
Estimated cost$1,620.00

A common mistake

Using the floor area as the roof area. A sloped roof is always bigger than the ground under it. Compare the footprint and the roof surface in the results before you order.

What is a roofing square?

Roofers price and order by the square. One square is 100 square feet (9.3 m²) of roof surface. The shingle packaging says how many bundles make a square, and that number differs from one product to another.

How much does pitch add to the area?

The steeper the roof, the more surface it has over the same footprint. The table shows the slope factor for common pitches and what each one does to 1,000 square feet of footprint. It is the same geometry the calculator uses.

Slope factor by roof pitch, for 1,000 ft² (92.9 m²) of footprint
PitchSlope factorRoof surface
2/121.0141,014 ft² (94.2 m²)
4/121.0541,054 ft² (97.9 m²)
6/121.1181,118 ft² (103.9 m²)
8/121.2021,202 ft² (111.7 m²)
10/121.3021,302 ft² (120.9 m²)
12/121.4141,414 ft² (131.4 m²)

How many bundles, and how much extra?

This guide does not assume a number of bundles per square. Type yours into the calculator and it works out the bundles from the squares, with your extra, and rounds up.

Every cut at a hip, a valley or an edge leaves a piece you cannot use, and the first row is cut to make a starter. A simple roof wastes less than a roof with many planes. Our 10% is a default, not a standard. Follow your shingle maker's instructions, and ask your supplier or roofer about your roof.

Frequently asked questions

How many roofing squares are in 1,500 square feet of roof?

A roofing square is 100 square feet, so 1,500 square feet is 15 squares. That is the roof surface, not the floor area of the house. A sloped roof is larger than the footprint under it.

How do I find my roof pitch?

Pitch is the inches of rise for every 12 inches of run. Hold a level horizontal against the roof, measure 12 inches along it, and measure straight up from that point to the roof. If the distance is 6 inches, the pitch is 6/12. If you cannot get on the roof, measure the gable end from the ground or ask a roofer.

Is the overhang included?

Only if you enter it. Building length and width are measured outside the walls, and the overhang is the extra the roof reaches past them on every side. The calculator adds it to both dimensions before it works out the roof surface.